 |
|
|
|
|
- VERTICAL AXIS
- Sensitivity: 5mV~5V/DIV, 10 steps in 1-2-5 sequence (X5 MAG: 1mV/DIV)
- Sensitivity accuracy: ≤3% (×5MAG: ≤5%)
- Vernier vertical sensitivity: continously variable to 1/2.5 or less of panel-indicated value
- Frequency bandwidth:
- DC-20MHz (×5MAG:DC-7MHz)
- DC-40MHz (×5MAG:DC-15MHz)
- AC coupling: Low limit frequency 10Hz. (With reference to 100KHz,8DIV.Frequency response with-3dB)
- Rise time: Approx.17.5Ns (×5MAG:Approx.50Ns) / 9.5nS (X5MAG: Approx.25nS)
- Input impedance: Approx. 1M ohm//Approx. 25pF
- Square wave characteristics:
- Overshoot: ≤5%(At 10Mv/DIV range) other distortions and other ranges: 5% added to the above value
- DC balance shift: 5mV~5V/DIV; ±0.5 DIV, 1mV~2mV/DIV±2.0DIV
- Linearity: ﹤ ±0.1DIV of amplitude change when waveform of 2 DIV at graticule center is moved vertically.
- Vertical modes:
- CH1 single channel.
- CH2 single channel
- DUAL: CH1 and CH2 are displayed ALT or CHOP selectable at any sweep rate.
- ADD: CH1+CH2 algebraic addition.
- Chopping repetition frequency: Approx.250KHz
- Input coupling: AC, GND , DC .
- Maximum input voltage: 300V peak (AC: frequency 1KHz or lower) When set probe switch at 1:1, the maximum effective readout is 40Vp p(14Vrms at sine wave); or set probe switch at 10:1, the maximum effective readout is 400Vpp(140Vrms at sine wave).
- Common mode rejection ratio: 50:1 or better at 50KHz sinusoidal wave.(when sensitivities of CH1 and CH2 are set equally)
- Isolation between channels (at 5Mv/DIV range): ＞ 1000:1 at 50 MHz; ＞ 30:1 at 20MHz; ＞ 30:1 at 40MHz
- CH1 signal output:
- At least 20Mv/DIV into a 50 ohm termination.
- Bandwidth is 50Hz to at least 5MHz.
- CH2 INV BAL: Balanced point variation: ≤1DIV(Reference at center graticule)
-
-
- TRIGGERING
- Triggering source: CH1,CH2,LINE,EXT.
- Coupling: AC:20Hz to full bandwidth
- Slope: +/-
- Sensitivity:
- 20Hz-2MHz: 1.0 DIV, TRIG-ALT: 2DIV,EXT:200Mv; 2MHz-20MHz: 1.5DIV; 20MHz or higher: 2.0DIV
- TRIG-ALT: 3DIV,EXT:800mv
- TV: Sync pulse more than 1 DIV (EXT:1V)
- Triggering modes:
- AUTO; NORM; TV-V; TV-H.
- (Both TV-V and TV-H synchronize only when the synchronizing signal is negative)
- EXT triggering signal input:
- Input impedance: Approx:1M ohm//approx.25pF
- Max input voltage: 300V(DC+AC peak), AC: frequency not higher than 1KHz.
-
- HORIZIONAL AXIS
- Sweep time: 0.2μSec-0.5Sec/DIV,20Steps in 1-2-5sequence.
- Sweep time accuracy: ±3%
- Vernier sweep time control: ≤1/2.5 of panel-indicated value.
- Sweep magnification: 10 times
- ×10MAG sweep time accuracy: ±5%(20nsec-50nsec are uncalibrated)
- Linearity: ±3%,×10MAG: ±5%(20ns and 50ns are uncalibrated)
- Position shift caused by×10MAG:Within 2 DIV, at CRT screen center.
- X-Y MODE
- Sensitivity: Same as vertical axis.(X-axis:CH1 input signal,Y-axis:CH2 input signal)
- Frequency bandwidth: DC to at least 500KHz
- X-Y phase difference: ≤3°at DC-50KHz
-
- Z AXIS
- Sensitivity: 5Vp-p (positive-going signal decreases intensity)
- Frequency bandwidth: DC-2MHz
- Input resistance: Approx,47k ohm
- Maximum input voltage: 30V (DC+AC peak, AC frequency ≤1KHz)
- CALIBEATION VOLTAGE
- Waveform: positive-going square wave
- Frequency: Approx,1KHz
- Output voltage:2Vp-p ±2%
- Output impedance: Approx,1K ohm
-
- CRT
- Type: 6-inch rectangular type, internal graticule
- Phosphor: P31
- Acceleration voltage: approx 2KV
- Effective screen size: 8x10 DIV(1 DIV=10mm(0.39in))
- Graticule: internal
- Trace rotation: provided
|
 |
NOTE ： |
- 20MHz/40MHz Dual Channel
- High Sensitivity 1Mv/DIV
- Z Axis Input
- CH1 Output
- 10 times sweep magnification
- TV Synchronization, X-Y mode
- High luminance, internal graticule
- Japanese electronic encoder, light, handy and reliable
- Fully sealed durable vertical mode switch
- ALT Triggering Function, simultaneous observation of two independant singals
- Triggering level lock function. Automatic synchronize function
|
|
|
|
|
|
 |
|
©2006 Matrix Technology Inc All rights reserved
Add： Building.B, No.5 East Wing, Shangxue Technology City, Bantian, Longgang, Shenzhen, China 518129
Tel： 0086 755 61217025 Fax： 0086 755 61217015 |
|